PW Marine OEM offers a complete inventory of warranty replacement, surplus, end-of-life, custom marine parts.
We also offer standard parts that can be utilized by both boat builders and boat owners.
If no items are listed within the category you are shopping, please contact our sales team to discuss your requirements.
Contact sales@pwmarineoem.com for custom or volume inquires
Marine Parts
Marine Parts
Filters
Filters
Two hole transom support plate in 316 stainless steel with a polished finish. It spreads the load of hardware fastened through the transom and reinforces the mounting area. Supplied without a logo.
Transom plates sit at the waterline area where splash and standing salt water are constant. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: PWB-TSP2-316SS
- Material: 316 stainless steel
- Finish: Polished
- Design: 2 hole, no logo
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a four hole transom support plate in 316 stainless steel, supplied without a logo. It spreads fastener load across the transom so mounted hardware does not crush or crack the laminate.
Backing and support plates are used behind transom mounted accessories such as tow eyes, ladders and brackets. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. The plain face lets builders use it across multiple models.
- Part number: PWB-TSP-316SS
- Material: 316 stainless steel
- Mounting: 4 hole
- Branding: No logo
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A three piece pontoon ski tow with a 46.5 top section. It raises the tow point above the deck so a skier, wakeboarder or tube line clears the motor and keeps a better pull angle.
Mounted to the rear deck structure of pontoon boats. 6061 aluminum offers a good strength to weight ratio and solid corrosion resistance. A polished finish gives a bright appearance, and periodic cleaning keeps it from dulling.
- Part number: PWB-STMH-V4-POL
- Material: 6061 aluminum
- Finish: Polished
- Construction: 3 piece
- Size: 46.5 top section
- Application: Pontoon
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This item is the finger set only for a Regal wake and surf rack. The fingers are the members that hold and separate the boards once the rack is installed.
Wake and surf racks are typically mounted on towers or above the gunwale to carry boards out of the cockpit. This listing covers the fingers alone and does not include the rest of the rack assembly or its mounting hardware.
- Part number: PWB-REG-SRF-F
- Contents: Fingers only
- Fitment: Regal wake/surf rack
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A port side bow rail for Yamaha F6H applications. The bow rail gives crew a secure hold at the bow and helps keep people aboard.
Bow rails are exposed to spray, sun and constant handling. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade.
- Part number: YJB-BR25PORT-316SS
- Material: 316 stainless steel
- Side: Port
- Fitment: Yamaha F6H
- Reference: F6H-2767-00
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
33 lb anchor with a slot, in polished 316 stainless steel, 812.8 mm (32 inches) overall. It holds the boat in position when deployed and stows at the bow roller.
Anchors are repeatedly submerged and dragged through sand and mud. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: YF-411111
- Material: 316 stainless steel
- Finish: Polished
- Weight: 33 lb
- Length: 812.8 mm (32 in) overall
- Type: With slot
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
These are threaded 2.5 inch stud plates for shock brackets in 316 stainless steel, for Tidewater Boats. They provide the threaded mounting studs that secure shock bracket hardware.
Shock bracket plates are used to mount shock absorbing seating or console hardware, where fasteners see repeated dynamic load. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater.
- Part number: TWB-SBTP-2.5
- Material: 316 stainless steel
- Size: 2.5 in. threaded studs
- Fitment: Tidewater Boats
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an anchor chute and trim piece for the 230CC, in polished 316 stainless steel. It guides the anchor and rode through the bow and protects the surrounding deck and gelcoat.
Anchor chutes sit at the bow, where they take direct spray and abrasion from the anchor and chain. 316 stainless resists salt water pitting better than 304, and the polished finish is easier to rinse clean of mud and salt.
- Part number: TWB-ACH-230CC-6P
- Material: 316 stainless steel
- Finish: Polished
- Fitment: 230CC
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Transom trim for the Tidewater Boats 37. The trim finishes and protects the edges of the transom.
Transom trim sees spray, line chafe and contact with gear, so it needs to hold up to the marine environment and keep a clean appearance on a highly visible edge of the boat. Contact our sales team to confirm material and finish.
- Part number: TWB-37TT-316SS
- Fitment: Tidewater Boats 37
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A seachest for the Tidewater 37. A seachest gathers raw water through the hull for supply to pumps and systems such as livewells and washdown.
Seachests sit below the waterline and are constantly in contact with raw water. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: TWB-37SC-316SS
- Material: 316 stainless steel
- Finish: Polished
- Fitment: Tidewater 37
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Chafe plate in polished 316 stainless steel. It protects the gelcoat where lines, anchor rode or other gear rub against the hull or deck.
Chafe plates are typically fitted at the bow, cleats and hawse areas. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: TWB-37CH-316SS
- Material: 316 stainless steel
- Finish: Polished
- Fitment: Tidewater 37
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a transom camera mount in cast, polished 316 stainless steel. It holds a camera at the transom for docking, rear view or trolling use.
Transom camera mounts are exposed to spray and wake. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. Casting allows a formed profile, and polishing helps the surface shed salt.
- Part number: TB-C7350PW
- Material: 316 stainless steel, cast
- Finish: Polished
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is transom trim for the Stingray Boats 269/73, in 316 stainless steel. It finishes and protects the transom edge.
Transom trim sits at the stern, where it takes spray, wake and contact from lines and gear. 316 stainless contains molybdenum for better resistance to salt water pitting than 304, which helps the trim keep its appearance over time.
- Part number: SRB-TT-316SS
- Material: 316 stainless steel
- Fitment: Stingray Boats 269/73
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A rod holder tab for SeaPro Boats. The tab provides a mounting point for a rod holder.
Rod holder mounts take bending loads from rods under strain and while running, so the mounting point needs to stay secure. Contact our sales team to confirm material, finish and dimensions for your build.
- Part number: SPB-RHT
- Type: Rod holder tab
- Fitment: SeaPro Boats
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A pair of armrest hinges for a leaning post. They allow the armrests to pivot up and down.
Leaning post hardware is handled constantly and exposed to spray at the helm. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade.
- Part number: SPB-LPARMHINGE
- Material: 316 stainless steel
- Quantity: Pair
- Fitment: Sea Pro leaning post
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Anchor roller bridge in 316 stainless steel, supplied as the bridge only. It is the part of the anchor roller assembly that spans the roller and keeps the rode and anchor captive.
Anchor rollers sit at the bow and take direct spray and wave impact. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: SPB-29AR-BRIDGE
- Material: 316 stainless steel
- Contents: Bridge only
- Fitment: Sea Pro 292
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard frame base plate for the top on the SeaPro 240DC. It anchors the starboard leg of the top frame to the deck or console.
Top frame base plates carry the loads from the T-top or hard top into the boat structure, including wind and wave loads underway. They should be bedded and fastened per the builder's specification.
- Part number: SPB-240STBD-PL
- Side: Starboard
- Fitment: SeaPro 240DC
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is the port top frame base plate for the Sea Pro Boats 240DC. The base plate is the mounting foot that attaches the top frame to the boat.
Top frame base plates sit at the attachment points of T-tops and hardtops, where they carry the load of the frame into the deck or console. Use the correct plate for each side so the frame aligns at installation.
- Part number: SPB-240PORT-PL
- Side: Port
- Fitment: Sea Pro Boats 240DC
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A top aft frame base plate for the SeaPro Boats 240DC. It provides the mounting base for the aft leg of the top frame at the deck.
Top frame base plates carry the load of the frame and canvas and see constant spray and vibration. A solid base plate spreads that load into the deck. Contact our sales team to confirm material and finish.
- Part number: SPB-240AFT-PL
- Position: Top aft frame base
- Fitment: SeaPro Boats 240DC
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A pantograph hinge assembly that moves a door or lid on a linked arm path, letting it open outward and clear of surrounding structure. This is the Assembly II version.
Pantograph hinges are used on doors and hatches where a standard hinge would not give enough clearance. 6061 aluminum offers a good strength to weight ratio, and hard anodizing creates a thick, wear resistant oxide layer that improves corrosion resistance.
- Part number: SOL-50002010
- Material: 6061 aluminum
- Finish: Hard anodized
- Reference: 2-000904
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Round drain cover plate for the starboard aft position, in polished 316 stainless steel. It covers the drain opening while letting water pass through.
Aft drains sit where water collects in the cockpit. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: SOL-300.04.072
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard, aft
- Fitment: Solace
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a port aft drain cover plate in polished 316 stainless steel for Solace. It covers a drain opening while letting water pass and keeping debris out of the drain line.
Drain cover plates sit in cockpit soles and deck channels where saltwater stands and flows. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: SOL-300.04.071
- Material: 316 stainless steel
- Finish: Polished
- Side: Port, aft
- Fitment: Solace
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is windshield hinge bracket A, cut from 0.25 inch 316 stainless steel plate and electropolished. It is one of the brackets that mounts and pivots a hinged windshield.
Windshield hinge brackets carry wind load and vibration at the helm. Electropolishing removes surface iron and microscopic peaks, which strengthens the passive layer of the 316 stainless and improves resistance to staining and corrosion.
- Part number: SOL-300.02.113
- Material: 316 stainless steel
- Finish: Electropolished
- Thickness: 0.25" plate
- Revision: 0
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A Solace drain cover plate for the XE, port side. It covers and finishes the drain opening while letting water clear.
Drain hardware sits where water and salt collect. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: SOL-300.01.344
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Solace XE
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A starboard drain cover plate for Solace boats. It covers the drain opening while letting water pass through.
Drain covers sit where water collects, so the material is regularly wet with salt water. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: SOL-300.01.343
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Fitment: Solace XC
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Transom trim in 316 stainless steel, designated 28HCS. It finishes and protects the transom edge.
Transom trim is exposed to constant splash and salt spray. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: SOL-300.01.329
- Material: 316 stainless steel
- Designation: 28HCS
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard drain cover plate in polished 316 stainless steel for Solace. It covers a drain opening while letting water pass and keeping debris out of the drain line.
Drain cover plates sit in cockpit soles and deck channels where saltwater stands and flows. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: SOL-300.01.161
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Fitment: Solace
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a port drain cover plate for Solace, in polished 316 stainless steel. It covers a drain opening while letting water pass through.
Drain cover plates are installed over deck, cockpit and compartment drains where water is constantly present. 316 stainless resists pitting in standing salt water better than 304, and the polished finish keeps the plate clean looking.
- Part number: SOL-300.01.160
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Solace
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A backer for the windshield actuator lower bracket. It reinforces the mounting area so the actuator bracket holds firm as the windshield moves.
Used behind actuator hardware where load and vibration are concentrated. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A PVD coating adds a hard, wear resistant colored surface over the stainless steel.
- Part number: SOL-2005533-PVDM
- Material: 316 stainless steel
- Finish: PVD coated
- Application: Windshield actuator lower bracket
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A windshield hinge bracket that allows a windshield section to pivot open and closed. It carries the windshield and holds it in alignment.
Windshield hinges are exposed to sun, spray and frequent use. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. PVD coating adds a thin, hard surface layer that resists wear and gives a consistent color.
- Part number: SOL-2005532-PVDM
- Material: 316 stainless steel
- Finish: PVD coated
- Model reference: A 30, 32, 38
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Windshield hinge bracket in 316 stainless steel with a PVD coated finish (PVDM). It supports the windshield hinge point on the console or deck.
Windshield hardware is fully exposed to sun and spray. 316 stainless steel resists salt corrosion, and a PVD coating adds a thin, hard layer that resists wear and fading.
- Part number: SOL-2005531-PVDM
- Material: 316 stainless steel
- Finish: PVD coated (PVDM)
- Designation: B 30, 32, 38
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard windshield hinge brace in 316 stainless steel with a PVDM (PVD coated) finish. It supports the windshield hinge and holds the windshield in position.
Windshield hinge braces are highly visible hardware at the helm. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A PVD coating adds a thin, hard color layer that resists wear and fading better than paint.
- Part number: SOL-2005530-PVDM
- Material: 316 stainless steel
- Finish: PVDM (PVD coated)
- Side: Starboard
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a port windshield hinge brace in 316 stainless steel with a PVD coated finish. It supports and stiffens the windshield at its hinge point.
Windshield hinge braces are used on boats with opening or hinged windshields, where the hardware sees wind load and vibration. 316 stainless resists salt water corrosion, and the PVD coating adds a thin, hard color layer over the steel.
- Part number: SOL-2005529-PVDM
- Material: 316 stainless steel
- Finish: PVD coated
- Side: Port
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A windlass bridge for the Solace 37. The bridge supports and positions the anchor windlass at the bow.
Windlass hardware takes heavy load from the anchor rode and sits in direct spray. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless.
- Part number: SOL-2-004003
- Material: 316 stainless steel
- Type: Windlass bridge
- Fitment: Solace 37
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A windlass bridge that provides the mounting point for the anchor windlass at the bow. It carries the windlass and helps guide the rode.
Windlass bridges sit at the bow where they take spray, rode wear and standing salt water. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: SOL-104474
- Material: 316 stainless steel
- Finish: Polished
- Model reference: 410
- Reference: 2-000850R1, updated 8/31/2020
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Offset dive door hinge in 316 stainless steel. It carries the dive door and lets it swing clear for boarding from the water.
Dive door hinges sit low in the hull side, where splash and standing salt water are constant. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: SMB-ODD-316SS
- Material: 316 stainless steel
- Type: Offset
- Fitment: Sportsman 402 (Pro)
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an angled swim platform in 316 stainless steel for Sportsman Boats. It provides a standing and boarding surface at the transom for swimming and boarding.
Swim platforms are mounted low on the transom and are constantly wet. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. That makes 316 the preferred grade for hardware in or near the water.
- Part number: SMB-FRV-316SS
- Material: 316 stainless steel
- Type: Angled
- Fitment: Sportsman Boats
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a four hole mounting bracket for a gas spring. It provides the anchor point for the end of a gas strut that lifts and holds a hatch, lid or seat open.
Gas spring brackets are used on hatches, fish boxes, seat bases and console lids. Proper bracket placement and secure fastening are key to getting the intended lift and hold from the gas spring.
- Part number: SMB-BRKT-4P
- Style: 4 hole
- Application: Gas spring mount
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A transom cap for Sportsman Boats, 34LF, triple configuration. The cap covers and finishes the top edge of the transom and protects it from wear.
Transom caps take foot traffic, line chafe and constant spray. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless.
- Part number: SMB-34LFTC-316SS
- Material: 316 stainless steel
- Configuration: 34LF, triple
- Fitment: Sportsman Boats
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An upper hardtop pad for the starboard side. Hardtop pads act as the mounting interface between the hardtop frame and the top, spreading load at the connection point.
Hardtop mounting pads are exposed to sun, spray and constant vibration underway, so material choice and correct fastening are important. Isolating dissimilar metals at the joint helps reduce galvanic corrosion.
- Part number: SMB-34LFPAD-S
- Location: Upper hardtop
- Side: Starboard
- Model reference: 34LF
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Upper port hardtop pad, designated 34LF. It is a support component at the hardtop mounting point that helps spread load where the top meets its frame.
Hardtop pads are used at the connection points of hardtops on center console boats. Matching the correct side and position keeps the top aligned during installation.
- Part number: SMB-34LFPAD-P
- Position: Upper
- Side: Port
- Designation: 34LF
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a two hole L shaped bracket, right side, in 316 stainless steel for Sportsman Boats. It joins or supports components at a right angle using a two fastener pattern.
L brackets are used throughout console, seating and structural assemblies to tie panels and frames together. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater.
- Part number: SMB-2HLB-RIGHT
- Material: 316 stainless steel
- Mounting: 2 hole
- Side: Right
- Fitment: Sportsman Boats
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a left hand, two hole L-shaped bracket for Sportsman Boats, in 316 stainless steel. It provides a right angle mounting point for components or structure.
L brackets are used inside consoles, under seats and at mounting points throughout the boat. 316 stainless resists salt water pitting and crevice corrosion better than 304, which matters for brackets that stay damp in enclosed spaces.
- Part number: SMB-2HLB-LEFT
- Material: 316 stainless steel
- Style: L-shaped, 2 hole
- Side: Left
- Fitment: Sportsman Boats
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Dive door trim for Sea Hunt 255, 275, 25, 27 and 30 models. The trim finishes the edges of the dive door opening and protects them from wear.
Dive door openings see heavy traffic from people and gear, plus constant spray. A trim piece keeps the opening clean and protects the laminate edge. Contact our sales team to confirm material and finish.
- Part number: SHB-DDTGF
- Fitment: Sea Hunt 255/275/25/27/30
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A dive door trim for the Sea Hunt 239. The trim finishes the edges of the dive door opening and gives a clean appearance.
Dive door trim sits at the hull side opening where it is regularly wet with salt water and handled during boarding. Corrosion resistant materials help it keep its finish.
- Part number: SHB-DDT239
- Type: Dive door trim
- Fitment: Sea Hunt 239
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Angled right end cap for the starboard side. It closes off and finishes the end of a rail or trim profile on the starboard side of the boat.
End caps protect exposed ends of trim and rails from snagging and water intrusion. Using the correct side specific cap keeps the finished line consistent.
- Part number: SHB-ARS-316
- Side: Right, starboard
- Type: Angled end cap
- Fitment: Sea Hunt
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an angled left end cap for the starboard side on Sea Hunt boats. It closes off the end of a rail or trim section and gives it a finished edge.
End caps protect exposed ends of rails and trim from snagging lines and from water entry. The angled profile is matched to the trim geometry on the starboard side.
- Part number: SHB-ALS-316
- Side: Left end cap, starboard side
- Type: Angled
- Fitment: Sea Hunt
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an angled left end cap for Sea Hunt. End caps finish the open end of a rail, trim or extrusion and protect the edge from damage.
End caps are typically used on gunwale trim, rub rail and rail ends where an open profile would otherwise be exposed. A capped end also keeps water and debris out of the profile.
- Part number: SHB-AL-316P
- Side: Left
- Style: Angled
- Fitment: Sea Hunt
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A right side 90 degree end cap for Sea Hunt. End caps close off the exposed end of a rail, trim or extrusion and leave a clean, safe corner.
End caps are small but visible finish parts, and on a saltwater boat they need to resist corrosion and staining. Contact our sales team to confirm material and finish for your build.
- Part number: SHB-90RIGHT-316
- Angle: 90 degree
- Side: Right
- Fitment: Sea Hunt
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A 90 degree left end cap for Sea Hunt boats. End caps close off and finish the open end of a rail, trim or extrusion.
End caps are used on rails, trim and extrusions throughout the deck and cockpit, where they are exposed to spray, sun and handling. Corrosion resistant materials help them keep a clean appearance over time, and a properly fitted cap keeps water and debris out of the open end.
- Part number: SHB-90LEFT-316
- Angle: 90 degree
- Side: Left
- Fitment: Sea Hunt
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Transom trim in anodized 6063 aluminum. It finishes the transom edge and gives the area a clean, consistent look.
6063 aluminum is an extrusion alloy with a smooth surface that takes anodizing well, which makes it common for trim profiles. Anodizing builds a hard oxide layer on the aluminum that resists corrosion and wear far better than bare metal in a marine setting.
- Part number: SHB-8608
- Material: 6063 aluminum
- Finish: Anodized
- Fitment: Sea Hunt
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a chafe plate in 316 stainless steel for the Sea Hunt 27. It protects the hull or deck surface where lines, anchor rode or chain would otherwise wear the gelcoat.
Chafe plates are fitted at the bow, around hawse openings and at line contact points. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater.
- Part number: SHB-27CP-316SS
- Material: 316 stainless steel
- Fitment: Sea Hunt 27
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an armrest cover plate kit for port and starboard. The cover plates close off and finish the armrest mounting area.
Armrest cover plates are used on helm seats, consoles and bench seating to give the armrest a clean, finished look and protect the mounting area. Confirm the original part number before ordering.
- Part number: SFB-1001
- Side: Port and starboard
- Contents: Cover plate kit
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A center drain gate for Sea Fox 288 and 368 models, version 2, supplied with no logo. It covers the drain opening and lets water clear the deck.
Deck drains see constant water, salt and foot traffic. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: SF-DGC-6P-V2
- Material: 316 stainless steel
- Finish: Polished
- Version: V2, no logo
- Fitment: Sea Fox 288/368
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A foot pad used at the port and starboard, front and rear mounting positions. Foot pads form the base where structure meets the deck and spread load at the connection point.
Foot pads are commonly used under hardtops, T-tops and leaning posts. A mill finish is supplied without a coating, so the part is suited to installations where it will be finished or covered.
- Part number: SF-30100143
- Finish: Mill finish
- Position: Port and starboard, front and rear
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Aluminum pad measuring 0.05 by 4 by 5 inches with a mill finish. It is used as a thin backing or support pad at a mounting point.
A mill finish is the untreated surface as produced, which suits parts that will be bonded, glassed in, covered or finished by the builder.
- Part number: SF-30100134
- Material: Aluminum
- Finish: Mill
- Dimensions: 0.05 in x 4 in x 5 in
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 5 inch by 3 inch pad in a mill finish, listed as a read pad. It provides a flat mounting or bearing surface for attached hardware.
Mounting pads are used to spread load and give a consistent seat for brackets and fittings. A mill finish is uncoated, so the part is typically installed out of sight or finished by the builder to suit the build.
- Part number: SF-30100123
- Finish: Mill finish
- Size: 5 in. x 3 in.
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 5 x 3.25 inch mounting pad for the front top position, port and starboard. Pads like this provide a flat bearing surface where a top or frame attaches to the boat.
Front top pads are typically used at the forward mounting points of T-tops, hardtops and frames. The part is supplied in a mill finish, so it can be painted, coated or installed as is to suit the build.
- Part number: SF-30100122
- Finish: Mill finish
- Dimensions: 5" x 3.25"
- Side: Port and starboard
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An outrigger plate for port and starboard. It provides the mounting base for outrigger hardware on the hardtop or gunwale.
Outrigger mounts take high bending loads from long poles, so a solid plate matters. A mill finish leaves the metal unfinished, so it is a good fit when the builder plans to paint, coat or cover the part.
- Part number: SF-30100117
- Finish: Mill finish
- Side: Port and starboard
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An aluminum pad kit for the Ultima 228TR. Pads act as mounting bases that spread load from fittings into the surrounding structure.
Mounting pads are used under structural hardware where a flat, stable base is needed. Anodizing builds a hard oxide layer on the aluminum that improves corrosion and wear resistance in a marine environment. A brushed finish gives a uniform appearance.
- Part number: SF-30100031
- Material: Aluminum
- Finish: Brushed anodized
- Type: Kit
- Fitment: Ultima 228TR
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Dive door hinge, 8 by 8 inches, in polished 316 stainless steel, designated 37. It carries the dive door and lets it swing open for boarding from the water.
Dive door hinges sit low in the hull side, where they see splash and standing salt water. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: S-SOL-2-004076
- Material: 316 stainless steel
- Finish: Polished
- Size: 8 in x 8 in
- Designation: 37
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a replacement swivel bolt for the Regal rack, reference 281635. It serves as the pivot bolt that lets the rack swivel or fold.
Swivel bolts on towers and racks see repeated movement and load, so worn or damaged bolts are a common replacement item. Keep the pivot clean and check fastener tightness regularly to keep the rack operating smoothly.
- Part number: REG-BOLTSWIV-REPLACE
- Fitment: Regal rack (281635)
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a receiver in 316 stainless steel. A receiver is the mating piece that accepts a latch, pin or fitting to hold a door, lid or component in place.
Receivers are used on doors, hatches and removable fittings throughout the boat. 316 stainless contains molybdenum, which gives it better resistance to salt water pitting than 304.
- Part number: PW069-REC
- Material: 316 stainless steel
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A spare stud for the PW046 bow roller assembly anchor chafe plate. It is a replacement fastener component for that assembly.
Keeping spare studs on hand lets a build line or service department complete or repair a bow roller assembly without replacing the full unit. Contact our sales team to confirm material and thread details for your application.
- Part number: PW046-STUD
- Application: PW046 bow roller assembly anchor chafe plate
- Type: Spare stud
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A bow roller assembly for the Sea Pro 319. It guides the anchor rode over the bow and supports the anchor as it is deployed and retrieved.
Bow rollers sit at the stem where they take spray and constant rode wear. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade.
- Part number: PW046
- Material: 316 stainless steel
- Type: Assembly
- Fitment: Sea Pro 319
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
16 inch grab rail made from oval tube with studs, in polished 316 stainless steel. It gives crew and passengers a secure handhold and mounts with 5/16 by 2 inch studs.
Grab rails are installed on consoles, gunwales and hardtops where people brace themselves. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: PW-8872S
- Material: 316 stainless steel
- Finish: Polished
- Length: 16 in, oval tube
- Studs: 5/16 in x 2 in
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 12 inch handrail in 316 stainless steel with a leather wrapped oval grip measuring 1 inch by 0.75 inch. It gives a secure handhold that is comfortable and less slippery than bare metal.
Leather wrapped handrails are used at helms, companion seats and dash areas where people hold on underway. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. The oval profile fits the hand well under load.
- Part number: PW-8712LW
- Material: 316 stainless steel
- Finish: Leather wrapped
- Size: 12 in., oval 1 in. x 0.75 in.
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is transom trim for the Pioneer Boats 22, in polished 316 stainless steel, updated V2 design. It finishes and protects the transom edge.
Transom trim sits where the hull meets the water and takes spray, wake and contact from lines and gear. 316 stainless resists salt water pitting better than 304, and a polished surface holds up visually at the stern.
- Part number: PB-TT220-316SS-V2
- Material: 316 stainless steel
- Finish: Polished
- Version: V2 updated
- Fitment: Pioneer Boats 22
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A large bow rail for the Parker Boats 254. Bow rails give crew a handhold and a safety barrier when working on the foredeck.
The bow takes the most spray on the boat, so rail material matters. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless.
- Part number: PB-LBR-316SS
- Material: 316 stainless steel
- Type: Large bow rail
- Fitment: Parker Boats 254
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An anchor roller for the Parker 254. It guides the anchor rode over the bow and holds the anchor in position when retrieved.
Anchor rollers sit at the bow where they take spray and wear from the rode. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: PB-AR254-316SS
- Material: 316 stainless steel
- Finish: Polished
- Fitment: Parker 254
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Drain fitting in polished 316 stainless steel, sold as a pair. It provides a finished drain opening that lets water exit the deck or compartment.
Drains sit where water collects and are often near or below the waterline. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: PB-2224D-316SS
- Material: 316 stainless steel
- Finish: Polished
- Quantity: Pair
- Fitment: Parker Boats
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a right side swing back seat support in polished 316 stainless steel. It carries and guides the swinging backrest so the seat can face forward or aft.
Swing back seats are used on consoles and lounges where one seat serves two directions, and the supports take load every time the backrest is moved. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: MOC-SBSR-6P
- Material: 316 stainless steel
- Finish: Polished
- Side: Right
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a left swingback seat support in polished 316 stainless steel. It carries the seat back on a swingback seat so the back can move between forward and aft facing positions.
Swingback seats are used on bow seating, cockpit benches and helm seats where a reversible backrest is wanted. 316 stainless resists salt water corrosion better than 304, which suits a structural part that is handled often and exposed to spray.
- Part number: MOC-SBSL-6P
- Material: 316 stainless steel
- Finish: Polished
- Side: Left
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A backing plate for the MasterCraft SurfStar. Backing plates reinforce the laminate behind hardware and spread fastener load across a wider area.
Used where mounted equipment sees load and vibration. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: MC-530602
- Material: 316 stainless steel
- Finish: Polished
- Fitment: MasterCraft SurfStar
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A welded support bracket for MasterCraft boats. It provides a fixed mounting and support point for attached components.
Support brackets are used where components need a rigid mount to the hull or deck. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A shaker polished finish gives a consistent, satin appearance.
- Part number: MC-530599
- Material: 316 stainless steel
- Finish: Shaker polished
- Construction: Welded
- Fitment: MasterCraft
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Table pedestal with a footrest rail in polished 304 stainless steel. It supports a cockpit or lounge table and gives seated passengers a place to rest their feet.
Table pedestals are common in lounge and entertainment areas. 304 stainless steel offers good corrosion resistance and strength, and it performs well in freshwater and lighter duty marine settings where it is rinsed and maintained.
- Part number: MBP-TP-FR-4P
- Material: 304 stainless steel
- Finish: Polished
- Reference: 002061
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an upper rail in polished 304 stainless steel, reference 002066. It forms the top rail section of a railing assembly, giving a handhold and perimeter guard.
Upper rails are used on bow, gunwale and deck railing systems. 304 stainless steel offers good general corrosion resistance, but in constant saltwater exposure it benefits from regular freshwater rinsing to limit surface staining. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: MBP-RU38-4P
- Material: 304 stainless steel
- Finish: Polished
- Size: 38' as listed
- Reference: 002066
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 9 foot aft rail in polished 304 stainless steel. It forms a perimeter rail and hand hold across the aft section of the deck.
Aft rails are common on pontoons and deck boats, where they define the stern area and give passengers support. 304 stainless works well in fresh water service, and in salt water it benefits from regular rinsing because it has less pitting resistance than 316.
- Part number: MBP-RA9-4P
- Reference: 002065
- Material: 304 stainless steel
- Finish: Polished
- Length: 9'
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A barstool pedestal, cross referenced as 002062. It supports a barstool style seat at a bar, wet bar or table area.
Pedestals carry the seat and occupant while the boat moves. 304 stainless steel offers good corrosion resistance and is a common choice for freshwater and sheltered applications, while saltwater use calls for regular rinsing to limit surface staining. The polished finish keeps it bright and easy to maintain.
- Part number: MBP-PB-4P
- Material: 304 stainless steel
- Finish: Polished
- Type: Barstool pedestal
- Reference: 002062
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A pair of L brackets used to join or support panels and components at a right angle. They provide a simple mounting point for fastening.
L brackets are used throughout consoles, lockers and seat bases. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade.
- Part number: HW-LBRACK
- Material: 316 stainless steel
- Quantity: Pair
- Reference: HW-0052
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Armrest center blade in polished 316 stainless steel, supplied with washer and nuts. It is the mounting blade that connects the armrest to the seat.
Armrest hardware carries load each time the operator braces or stands. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: HW-0053
- Material: 316 stainless steel
- Finish: Polished
- Includes: Washer and nuts
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard switch panel in polished 316 stainless steel. It mounts and frames electrical switches at the helm or console on the starboard side.
Switch panels are installed at helms and consoles where they are exposed to spray and frequent handling. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: HCB-HS-99120-STBD
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a port side switch panel in polished 316 stainless steel. It provides the mounting face for switches and controls at the helm or console.
Switch panels are installed in dashes, consoles and helm stations where they are exposed to spray and frequent handling. 316 stainless resists salt water corrosion better than 304, and the polished finish keeps a clean, consistent look at the helm.
- Part number: HCB-HS-99120-PORT
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A gutter drain trim cover plate for the HCB 53. It covers and finishes the gutter drain opening while letting water run off.
Gutter drains carry water and salt residue continuously. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: HCB-GDTCP-316SS
- Material: 316 stainless steel
- Finish: Polished
- Fitment: HCB 53
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A dive gate door hinge that carries the dive door as it swings open and closed. It supports the door and allows clear access for boarding from the water.
Dive door hinges sit at the hull side or transom where they are regularly wet with salt water. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade.
- Part number: HCB-DDH-316SS
- Material: 316 stainless steel
- Dimensions: 8 in. x 8 in.
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Starboard transom trim cover in 316 stainless steel. It finishes and protects the edge of the transom area.
Transom trim is exposed to constant splash and salt spray. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: HCB-21115A
- Material: 316 stainless steel
- Side: Starboard
- Fitment: HCB 56
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a port transom trim cover in 316 stainless steel for the HCB 56. It covers and finishes a transom edge or opening on the port side.
Transom trim is exposed to spray, wake and dockside contact. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. That matters on a large offshore hull that spends long periods in saltwater.
- Part number: HCB-21114A
- Material: 316 stainless steel
- Side: Port
- Fitment: HCB 56
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 1 1/2 inch adhesive back EPDM foam gasket for a tilt out helm air conditioning plenum. It seals the plenum against the helm structure to keep conditioned air flowing where it is intended.
Adhesive foam gaskets are used on helm panels, access hatches and duct connections. EPDM resists water, UV and ozone well, so it keeps its seal in a marine helm environment.
- Part number: HCB-19512A
- Material: EPDM foam
- Width: 1 1/2"
- Backing: Adhesive
- Application: Tilt out helm AC plenum
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A 6mm drain grate for cockpit tubs, designated 48. It covers the drain so water clears the tub while debris stays out of the plumbing.
Cockpit tubs hold standing water, fish slime and salt, so drain hardware needs to resist corrosion. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless.
- Part number: HCB-19075A
- Material: 316 stainless steel
- Thickness: 6mm
- Designation: 48
- Application: Cockpit tubs
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A headrest bracket for a transom center seatback. It supports the upholstered headrest and attaches it to the seat structure.
Headrest brackets are fitted to transom seating that takes spray and direct sun. 6061 aluminum offers a good strength to weight ratio, and anodizing builds a hard oxide layer that improves corrosion and wear resistance.
- Part number: HCB-19014A
- Material: 6061 aluminum
- Finish: Dark grey anodized
- Location: Transom center seatback headrest
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Headrest bracket for a port transom seatback in 6061 aluminum with a dark grey anodized finish. It mounts the headrest to the transom seatback.
Transom seating is exposed to spray and sun. 6061 aluminum offers a good balance of strength and machinability, and anodizing builds a hard oxide layer that resists corrosion and wear in a marine setting.
- Part number: HCB-19006A
- Material: 6061 aluminum
- Finish: Dark grey anodized
- Side: Port
- Designation: 48 transom
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a headrest bracket in 6061 aluminum, anodized dark grey, for a 48 console seatback on the port upholstery side. It supports and positions the headrest on the seatback.
Headrest brackets are visible seating hardware at the console. Anodizing builds a hard oxide layer on the aluminum that resists corrosion and surface wear. The dark grey anodize gives a uniform color that resists fading compared with paint.
- Part number: HCB-18762A
- Material: 6061 aluminum
- Finish: Anodized dark grey
- Side: Port
- Application: 48 console seatback
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a headrest bracket for a bow port seatback upholstery assembly, made from 6061 aluminum and anodized dark grey. It mounts the headrest to the upholstered seatback.
Headrest brackets are used in bow seating and lounges where a cushioned headrest attaches to the seat structure. Anodizing builds a hard oxide layer on the aluminum that improves corrosion and wear resistance, and the dark grey color stays out of sight behind upholstery.
- Part number: HCB-18712A
- Material: 6061 aluminum
- Finish: Anodized dark grey
- Side: Port, bow
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A custom mechanical striker plate. The striker gives a latch a fixed point to engage so doors, hatches and lids stay closed.
Striker plates take repeated contact from the latch and need to resist wear and corrosion. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless.
- Part number: HCB-18048A
- Material: 316 stainless steel
- Type: Custom mechanical striker plate
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A bolster cushion foam for Sea Fox boats, supplied as foam only without the backing board. It forms the padded core of a bolster cushion.
Bolster cushions are used at the gunwale and leaning post to pad crew while standing. The foam is supplied without the board so it can be fitted to an existing backing and upholstery.
- Part number: HA-PW-01-V2
- Material: Foam
- Includes: Foam only, without board
- Fitment: Sea Fox
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Air ride aluminum seat pedestal with height from 400 to 500 mm and a 9 inch base and post, anodized. It supports a helm or passenger seat and absorbs ride motion.
Air ride pedestals are used at helm stations to reduce operator fatigue in rough water. Anodizing builds a hard oxide layer on the aluminum that resists corrosion and wear far better than bare metal in a marine setting.
- Part number: HA-D-04.02
- Material: Aluminum
- Finish: Anodized
- Height: 400 to 500 mm
- Base and post: 9 in
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is armrest foam for Sea Pro captain chairs, supplied as foam only. It forms the padded core of the chair armrest under the upholstery.
Armrest foam is typically replaced when upholstery is redone or when the original foam has compressed or absorbed water. This item is foam only, so the cover and any hard components are sourced separately.
- Part number: HA-C-19H
- Material: Foam
- Fitment: Sea Pro captain chairs
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a right armrest hinge assembly in polished 316 stainless steel with a 106 degree setting. It lets an armrest fold up and down and sets its lowered position.
Armrest hinges are used on helm chairs, captain seats and leaning posts. 316 stainless resists salt water corrosion better than 304, and the polished finish helps the moving joint stay clean and free of staining.
- Part number: H47001RARM-106
- Material: 316 stainless steel
- Finish: Polished
- Angle: 106 degrees
- Side: Right
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A right armrest hinge assembly with 100 degree travel, cross referenced as 40151. It lets the armrest pivot up and out of the way and return to a stable position for use.
Used on helm and companion seats. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: H47001RARM-100
- Material: 316 stainless steel
- Finish: Polished
- Opening: 100 degree
- Side: Right
- Reference: 40151
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A left armrest hinge assembly that lets the armrest pivot between up and down positions. It is set to a 106 degree position.
Armrest hinges are used on helm seats and leaning posts where hardware is handled constantly and exposed to spray. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: H47001LARM-106
- Material: 316 stainless steel
- Finish: Polished
- Side: Left
- Angle: 106 degree
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Left armrest hinge assembly set at 100 degrees, in polished 316 stainless steel. It lets the armrest pivot up and down on the seat.
Armrest hinges are cycled constantly on helm and passenger seating. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: H47001LARM-100
- Material: 316 stainless steel
- Finish: Polished
- Angle: 100 degrees
- Side: Left
- Reference: 40152
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a custom high speed intake in 316 stainless steel for Freeman, version 2. It picks up water while the boat is on plane to feed a raw water circuit such as a livewell or washdown.
High speed intakes are mounted below the waterline and stay submerged in use. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. That makes it the preferred grade for through hull hardware.
- Part number: FBW-HSI-316SS-V2
- Material: 316 stainless steel
- Version: 2
- Fitment: Freeman
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an angled right end cap for Freeman, in polished 316 stainless steel. End caps finish the open end of a rail, trim or extrusion and protect the edge from damage.
End caps are used on gunwale trim, rub rail, rails and edge profiles. 316 stainless resists salt spray better than 304, and the polished surface matches surrounding bright hardware.
- Part number: FBW-ECR-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Right
- Style: Angled
- Fitment: Freeman
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A left side angled end cap for Freeman. End caps close off the exposed end of a rail, trim or extrusion and leave a clean, safe edge.
Small finish parts like end caps are highly visible and must not stain. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: FBW-ECL-316SS
- Material: 316 stainless steel
- Finish: Polished
- Style: Angled
- Side: Left
- Fitment: Freeman
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A 4 step box ladder with black steps, a sealed box and a V2 face plate. The ladder stows inside its box and deploys for boarding from the water.
Box ladders are installed in the hull side or transom so the ladder sits flush when stowed. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: FBW-BXLD-316SS
- Material: 316 stainless steel
- Finish: Polished
- Steps: 4, black
- Features: Sealed box, V2 face plate
- Fitment: Freeman
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Starboard strap assembly in polished 316 stainless steel. It is a structural strap used to secure and support components at its mounting location.
Strap assemblies are used where hardware must be tied into the boat structure under load. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: FBW-47S-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Fitment: Freeman 47
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a port strap assembly in polished 316 stainless steel for the Freeman 47. It is a structural strap used to tie together or support mounted components on the port side.
Structural straps carry load between mounting points and are often exposed to spray. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: FBW-47P-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Freeman 47
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is the starboard strap assembly for the Freeman Boats 38, in polished 316 stainless steel. A strap assembly ties hardware or structure together and spreads loads across the mounting area.
Structural straps are used where tops, frames or deck hardware need reinforcement. 316 stainless offers better chloride corrosion resistance than 304, which matters for load carrying parts in salt water service.
- Part number: FBW-38S-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Fitment: Freeman Boats 38
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A port strap assembly for Freeman Boats 38. Strap assemblies tie structure together and provide a secure mounting point for connected components.
Exposed structural hardware needs to hold up to salt and load at the same time. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: FBW-38P-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Freeman Boats 38
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A starboard side strap assembly for a Freeman Boatworks 35. Strap assemblies tie structure together and transfer load to the hull or deck at the mounting point.
Structural strap hardware is exposed to spray and vibration underway. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: FBW-35S-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Fitment: Freeman Boatworks 35
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Port strap assembly in polished 316 stainless steel. It is a structural strap used to secure and support components at its mounting location.
Strap assemblies are used where hardware must be tied into the boat structure under load. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: FBW-35P-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Freeman Boatworks 35
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard tow eye assembly in polished 316 stainless steel for the Freeman 29. It provides the attachment point for towing or trailering lines at the hull.
Tow eyes take high point loads and are located low on the hull where they are often wet. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: FBW-29S-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Fitment: Freeman 29
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is the port tow eye assembly for the Freeman 29, in polished 316 stainless steel. It provides a hard attachment point for towing, trailering or securing the boat.
Tow eyes are mounted at the bow or transom and carry significant loads in a wet, salt exposed location. 316 stainless resists pitting and crevice corrosion better than 304, and the polished finish reduces sites where corrosion can start.
- Part number: FBW-29P-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Freeman 29
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A starboard strap assembly for the Freeman 28. Strap assemblies tie structure together and provide a secure mounting point for connected components.
Exposed structural hardware needs to hold up to salt and load at the same time. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: FBW-28S-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Fitment: Freeman 28
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A port side strap assembly for a Freeman 28. Strap assemblies tie structure together and transfer load to the hull or deck at the mounting point.
Structural strap hardware is exposed to spray and vibration underway. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: FBW-28P-316SS
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Freeman 28
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Shock bracket in 316 stainless steel, designated F8J, EG. It mounts a shock absorber to the boat structure.
Shock brackets take repeated load in exposed locations. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: F8J-U2899-00
- Material: 316 stainless steel
- Designation: F8J, EG
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 316 stainless steel camera mount plate with a hole for cable or fastener pass through. It provides a solid mounting surface for a camera on the boat.
Camera mount plates are used on transoms, T-tops and hard tops for docking, security or trolling cameras. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater.
- Part number: F6P-U777G-00
- Material: 316 stainless steel
- Feature: With hole
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a stainless steel pod bar in 316 stainless steel. It is a formed bar used as a structural or trim member on a pod assembly.
The part is both polished and electropolished. Electropolishing removes surface iron and microscopic peaks after mechanical polishing, which strengthens the passive layer and improves resistance to staining and corrosion in salt water.
- Part number: F6P-U3748-10
- Material: 316 stainless steel
- Finish: Polished and electropolished
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An F6P head door latch bracket for the port side. The bracket positions and supports the latch so the head door closes and holds securely.
Head door hardware is opened and closed often and is exposed to humid air. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: F6P-U3166-00
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Designation: F6P
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A shock bracket that provides the mounting point for a gas shock or strut. It transfers load from the shock into the surrounding structure.
Shock brackets are used on hatches, lids and seat bases. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. Electropolishing removes surface iron and microscopic peaks, improving passivation and helping the part resist tea staining.
- Part number: F6P-U2899-50
- Material: 316 stainless steel
- Finish: Electropolished
- Reference: F6P-U2899-50
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Electropolished 316 stainless steel shock bracket, designated F6P. It mounts a shock absorber to the boat structure.
Shock brackets take repeated load and sit in exposed locations. 316 stainless steel resists salt corrosion, and electropolishing removes surface imperfections and leaves a passive, smooth surface that further improves corrosion resistance.
- Part number: F6P-U2899-40
- Material: 316 stainless steel
- Finish: Electropolished
- Designation: F6P
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an aluminum walk through brace with a brushed, anodized finish. It stiffens and supports the structure at a walk through opening, such as a windshield or console passage.
Walk through braces are visible structural parts, so finish matters as much as strength. Anodizing builds a hard oxide layer on the aluminum that resists corrosion and surface wear. The brushed texture gives a consistent satin appearance.
- Part number: F6P-U2891-00
- Material: Aluminum
- Finish: Brushed, anodized
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a head door sill plate with a latch lock, made without a flange, in polished 316 stainless steel. It protects the door sill from wear and provides the engagement point for the head door latch.
Sill plates are installed at head and cabin door openings that see constant foot traffic. 316 stainless resists salt air corrosion better than 304, and the polished finish keeps a clean appearance in a humid space.
- Part number: F6P-U284F-01
- Material: 316 stainless steel
- Finish: Polished
- Style: Latch lock, no flange
- Revision: TA
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An F6P bow plate, Revision 2. Bow plates protect the deck and stem from wear where anchor rode and chain run over the bow.
The bow takes direct spray and abrasion from chain and line. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless.
- Part number: F6P-U2569-00-R2
- Material: 316 stainless steel
- Designation: F6P, Rev. 2
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An anchor rode assembly combining twisted nylon rope, high test chain and shackles. It connects the anchor to the boat and is ready for installation in the anchor locker.
Three strand nylon stretches under load, which helps absorb shock while at anchor. The chain section adds weight at the anchor and resists abrasion on the bottom.
- Part number: F6P-U2529-00
- Material: Twisted nylon 3 strand rope with G4 high test chain
- Rope: 1/2 in. diameter, 100 ft. length
- Chain: 1/4 in. diameter, 10 ft. length
- Shackles: 5/16 in. and 3/8 in.
- Reference: SHPL-01
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Three step telescoping undermount boarding ladder in polished 316 stainless steel. It extends from under the platform for reboarding and retracts for stowage.
Undermount ladders stay out of sight but are submerged during use. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: F6P-U2425-00
- Material: 316 stainless steel
- Finish: Polished
- Steps: 3, telescoping, undermount
- Fitment: Yamaha
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an L bracket in 6061 aluminum for mounting a steering pump. It holds the hydraulic steering pump in position behind the helm.
Steering pump brackets are installed behind the dash or inside the console, out of direct spray. 6061 aluminum is a strong, corrosion resistant structural alloy. A raw finish is uncoated, so the part is typically installed out of sight or finished by the builder to suit the build.
- Part number: F6P-U1794-10
- Material: 6061 aluminum
- Finish: Raw
- Type: L bracket
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an L bracket in 6061 aluminum, 0.125 inch thick, with deburred edges. It provides a right angle mounting point for panels, components and structure.
L brackets are used throughout consoles, under decks and inside compartments to join or support parts. 6061 aluminum offers a good balance of strength, light weight and corrosion resistance, and deburring removes sharp edges for safer handling and installation.
- Part number: F6M-U5937-10
- Material: 6061 aluminum
- Finish: Deburred
- Thickness: 0.125"
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A Yamaha trolling motor mount with a white powder coated finish. It provides a fixed base for mounting the trolling motor to the boat.
Usually installed at the bow, where the mount takes spray and load from the motor. 6061 aluminum offers a good strength to weight ratio. Powder coating adds a durable color finish that resists UV and abrasion, and isolating aluminum from dissimilar metals at install helps prevent galvanic corrosion.
- Part number: F6H-U8577-10
- Material: 6061 aluminum
- Finish: White powder coat
- Fitment: Yamaha trolling motor
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A trolling motor mount that provides the mounting base for a bow trolling motor. It carries the motor and transfers its load to the deck.
Trolling motor mounts sit at the bow where they take spray, impact and vibration. A powder coated finish provides a durable barrier against moisture, UV and salt, and white powder coat stays cooler in direct sun.
- Part number: F6A-U8577-00
- Finish: White powder coat
- Fitment: Yamaha
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Forward console grab bar, 406 mm (16 inches), in polished 316L stainless steel. It gives passengers a secure handhold at the front of the console.
Grab bars are used where crew brace themselves in a seaway. 316L is a low carbon version of 316 that keeps its corrosion resistance at welds, which suits welded tube hardware in saltwater use.
- Part number: EWT8-72-8824
- Material: 316L stainless steel
- Finish: Polished
- Length: 406 mm (16 in)
- Position: Forward console
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard forward bow rail with studs, in polished 316L stainless steel, for the Nimbus T8. It provides a secure handhold and perimeter rail at the bow.
Bow rails are fully exposed to spray and handled constantly when anchoring and docking. 316L is the low carbon version of 316 stainless steel, which keeps its corrosion resistance at welded joints. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: EWT8-72-8804
- Material: 316L stainless steel
- Finish: Polished
- Side: Starboard, forward
- Mounting: With studs
- Fitment: Nimbus T8
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is the port forward bow rail with studs for the Nimbus T8, in polished 316L stainless steel. It forms the forward perimeter rail on the port side of the bow and mounts through its integrated studs.
Bow rails give crew a secure hold when working on the foredeck. 316L is a low carbon version of 316 that keeps its corrosion resistance at welded joints, and the polished finish helps prevent tea staining.
- Part number: EWT8-72-8803
- Material: 316L stainless steel
- Finish: Polished
- Side: Port, forward
- Fitment: Nimbus T8
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An end cap for the Nimbus T8. End caps finish and close off the exposed end of a rail, trim or extrusion and give it a clean, safe edge.
316L is a low carbon grade of 316 stainless steel that keeps its corrosion resistance after welding and performs well in saltwater. A polished finish keeps the part bright and easy to clean.
- Part number: EWT8-12-8902
- Material: 316L stainless steel
- Finish: Polished
- Fitment: Nimbus T8
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A wide upholstery clip used to attach seat cushions and upholstered panels to their mounting surfaces. This version has no countersink holes.
Upholstery clips are fitted throughout seating and bolster installations where cushions need to be removable. Aluminum is light and corrosion resistant for hardware hidden behind upholstery.
- Part number: EWB-WUP-AL
- Material: Aluminum
- Style: Wide, no countersink holes
- Fitment: Edgewater
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Angled hardtop drain in polished 316 stainless steel. It channels water off the hardtop so it does not pool or run onto the deck.
Hardtop drains are mounted overhead in direct sun and spray. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: EWB-72-8837
- Material: 316 stainless steel
- Finish: Polished
- Type: Angled hardtop drain
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an anchor chafe plate. It protects the bow from wear where the anchor, chain or rode contacts the hull or deck during deployment and retrieval.
Chafe plates are fitted at the bow around the anchor roller or locker opening, where the anchor and chain rub against gelcoat. A metal plate takes that wear so the hull surface does not have to.
- Part number: EWB-72-0071
- Fitment: 318CC/325CC, 262CC/CX
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an aluminum backing plate measuring 3/4 x 6 x 1/8 inches. A backing plate sits behind a deck, liner or panel to spread fastener loads and keep hardware from pulling through.
Backing plates are commonly used under cleats, rails, brackets and other through-bolted hardware. Aluminum is light and does not rust, though it should be isolated from stainless fasteners in wet areas to limit galvanic corrosion.
- Part number: CY-6
- Material: Aluminum
- Dimensions: 3/4" x 6" x 1/8"
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An aluminum backing plate measuring 1" x 23" x 1/8". Backing plates reinforce the laminate behind a fitting and spread fastener load over a larger area.
Used behind rails, brackets and other hardware that see pull-out loads. Aluminum keeps weight down and resists corrosion, and it should be isolated from stainless fasteners to limit galvanic corrosion.
- Part number: CY-142
- Material: Aluminum
- Dimensions: 1" x 23" x 1/8"
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An aluminum backing plate that sits behind a panel or deck to spread the load from through bolted hardware. It reduces point loading and helps prevent fasteners from pulling through.
Backing plates are used under rails, cleats, seat bases and other bolted hardware. Aluminum is light and corrosion resistant, and isolating it from stainless fasteners helps reduce galvanic corrosion.
- Part number: CY-141
- Material: Aluminum
- Dimensions: 1 in. x 19 in. x 1/8 in.
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Aft gate assembly in polished 316 stainless steel for a pontoon deck. It forms the gated opening at the aft end of the deck fencing.
Gate assemblies are opened and closed often and stay exposed to weather. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: CRST-2001252
- Material: 316 stainless steel
- Finish: Polished
- Position: Aft
- Fitment: Balise SLS
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a polished 316 stainless steel port storage gate for the Balise. It closes off a storage opening on the port side to keep gear contained.
Storage gates are used on pontoon and deck boat layouts where open storage needs a secure, visible closure. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: CRST-2001039
- Material: 316 stainless steel
- Finish: Polished
- Side: Port (L)
- Fitment: Balise
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a port side galley storage gate in polished 316 stainless steel for the Balise. The gate closes off the galley storage area and keeps contents contained.
Galley gates are used on pontoon and deck boat layouts with built-in galley or bar storage. 316 stainless resists corrosion better than 304 in wet and salt environments, and the polished finish is easy to wipe down around food and drink areas.
- Part number: CRST-2001036
- Reference: 2001036, C
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Balise
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A standing drink holder with a full ring, sized for 4-1/8" and 5-1/8" tall containers. It keeps drinks upright and in place while the boat is moving.
Mounted near seating and helm areas where passengers need a secure spot for a cup or can. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: CRST-2000779
- Material: 316 stainless steel
- Finish: Polished
- Size: 4-1/8" and 5-1/8" tall, full ring
- Fitment: Balise
- Reference: 2000779
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A standing drink holder with a full ring that holds a cup or can upright. It is 3-5/8 in. tall.
Drink holders are mounted at seating, consoles and rails where they are handled often and exposed to spray. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: CRST-2000778
- Material: 316 stainless steel
- Finish: Polished
- Height: 3-5/8 in.
- Style: Standing, full ring
- Fitment: Balise
- Reference: 2000778
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Galley storage gate in polished 316 stainless steel. It closes off the galley storage area on a pontoon deck.
Pontoon galley and storage hardware is handled daily and exposed to weather. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: CRST-2000776
- Material: 316 stainless steel
- Finish: Polished
- Reference: 2000776
- Fitment: Balise
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard helm accent trim kit for the Balise. It provides the trim pieces that finish the starboard side of the helm area.
Accent trim is used to finish edges and transitions at the helm and give the console a consistent look. Trim exposed to sun and spray should be cleaned with fresh water and mild soap to keep the finish looking new.
- Part number: CRST-2000690
- Side: Starboard
- Type: Helm trim kit
- Fitment: Balise
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard rear rail in polished 316 stainless steel for the Balise. It provides a hand hold and perimeter rail at the aft starboard side of the deck.
Rear rails are used at the stern for support when moving around the deck and boarding. 316 stainless offers better pitting resistance than 304, and a polished finish keeps a bright surface that is easier to maintain.
- Part number: CRST-2000673
- Reference: 2000673
- Material: 316 stainless steel
- Finish: Polished
- Side: Starboard
- Fitment: Balise
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A port side rear rail for the Balise. It gives passengers a handhold at the rear of the deck and helps finish the perimeter of the seating area.
Rear rails are handled constantly and exposed to weather. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: CRST-2000672
- Material: 316 stainless steel
- Finish: Polished
- Side: Port
- Fitment: Balise
- Reference: 2000672
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An aft hand rail that gives passengers a secure hold when moving about the aft deck. Grab rails provide support while boarding and moving around underway.
Hand rails are handled constantly and exposed to sun and spray. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: CRST-2000667
- Material: 316 stainless steel
- Finish: Polished
- Location: Aft
- Fitment: SLS, Balise
- Reference: 2000667
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Wind door catch in polished 316 stainless steel. It holds the windshield door in the open position so it does not swing.
Wind door catches are used on console windshields and walk through doors. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: CIG-WDC-316SS
- Material: 316 stainless steel
- Finish: Polished
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 2 inch by 1.5 inch offset hinge in polished 316 stainless steel. The offset leaf lets a door or lid sit flush or clear an adjacent edge when the mounting surfaces are not on the same plane.
Offset hinges are used on console doors, hatches and lids where the door is recessed or overlaps the frame. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: CIG-HINGE-OF
- Material: 316 stainless steel
- Finish: Polished
- Size: 2 in. x 1.5 in.
- Type: Offset
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a cabin door catch in polished 316 stainless steel. It holds a cabin door closed, or open against a stop, so it does not swing while the boat is running.
Door catches are installed on cabin entries, head doors and console doors. 316 stainless resists salt air corrosion better than 304, and the polished finish keeps a clean appearance at a high visibility, high touch location.
- Part number: CIG-CDC-316SS
- Material: 316 stainless steel
- Finish: Polished
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A custom anchor pin bracket. It holds the anchor pin in place at the bow so the anchor stays secured while the boat is running.
Bow hardware takes direct spray and contact with wet anchor chain and line. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: CIG-APB-6P
- Material: 316 stainless steel
- Finish: Polished
- Type: Custom anchor pin bracket
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A stainless steel heat shield plate for a grill installation. It protects the surrounding structure and surfaces from grill heat.
Grill heat shields are used in outdoor galley and entertainment centers on cockpits and swim platforms. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: AV-530171
- Material: 316 stainless steel
- Finish: Polished
- Dimensions: 26.65 in. x 13.93 in.
- Model reference: AV32
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Forward seat backrest bracket, part A, in polished 316 stainless steel, revision B. It supports and attaches the backrest to a forward seat.
Forward seating sees direct spray and sun. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: 8441119-B
- Material: 316 stainless steel
- Finish: Polished
- Revision: B
- Component: Part A
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 12 inch grab rail for Sea Hunt boats. It gives passengers and crew a secure handhold when moving around the deck or boarding.
Grab rails are mounted on consoles, gunwales, T-top frames and seat backs, where they take load from people bracing against boat motion. Rails used in a saltwater environment should be rinsed with fresh water to keep the finish clean.
- Part number: 66840307
- Size: 12 in.
- Fitment: Sea Hunt
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a swim step tie bar in 304 stainless steel, referenced as MEP. A tie bar connects and braces the swim step structure so it stays rigid under load.
Swim step tie bars sit at the stern, where they are wet much of the time. 304 stainless performs well with routine rinsing and is often used in fresh water applications; in salt water it has less pitting resistance than 316.
- Part number: 602229
- Material: 304 stainless steel
- Reference: MEP
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A port side swim step kit in 304 stainless steel, designated MEP and A40. The kit provides a step for boarding from the water or the swim platform.
Swim steps spend much of their life wet. 304 stainless steel offers good corrosion resistance and is a common choice for freshwater and sheltered applications, while saltwater use calls for regular rinsing to limit surface staining. Confirm configuration details with our sales team before ordering.
- Part number: 602228
- Material: 304 stainless steel
- Side: Port
- Designation: MEP, A40
- Type: Kit
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A swim step kit for the port side. Swim steps give swimmers a foothold for boarding from the water or from a swim platform.
Swim steps are mounted at the transom or hull side where they are repeatedly immersed. 304 stainless steel offers good general corrosion resistance, and regular rinsing helps prevent tea staining in salt water.
- Part number: 602227
- Material: 304 stainless steel
- Side: Port
- Type: Kit
- Reference: MEP, A40
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Starboard swim platform bracket kit. It provides the bracket hardware used to mount the swim platform to the hull on the starboard side.
Swim platform brackets carry the platform at the transom, an area exposed to splash and wave loads. Using the correct side specific bracket keeps the platform aligned and properly supported.
- Part number: 601956PW
- Type: Kit
- Side: Starboard
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a port swim platform bracket kit. The brackets attach the swim platform to the transom on the port side and carry the platform load.
Swim platform brackets are mounted low on the transom and are frequently in contact with water. Bracket kits are typically ordered alongside the matching starboard kit, so confirm both sides for your build.
- Part number: 601955PW
- Side: Port
- Type: Kit
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 44 inch adjustable bimini pole in polished 304 stainless steel. It supports a bimini top and adjusts to set the height or tension of the canvas.
Bimini poles are used on pontoons, runabouts and deck boats to hold a shade top in place. 304 stainless is a common choice for above-deck hardware, and the polished finish helps it resist staining with regular freshwater rinsing.
- Part number: 464990
- Material: 304 stainless steel
- Finish: Polished
- Length: 44"
- Style: Adjustable
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An adjustable 37" bimini pole. It supports the bimini top frame and can be set to the length needed for the installation.
Bimini poles are fitted between the top frame and the deck or gunwale. 304 stainless steel offers good corrosion resistance and is a common choice for freshwater and sheltered applications, while saltwater use calls for regular rinsing to limit surface staining. The polished finish keeps the pole bright and easy to clean.
- Part number: 464988
- Material: 304 stainless steel
- Finish: Polished
- Length: 37", adjustable
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An adjustable bimini pole used to support and tension a bimini top. Adjustment allows the top to be set to the correct height and fabric tension.
Bimini poles are used on pontoons, runabouts and center consoles to support shade tops. 304 stainless steel offers good general corrosion resistance and is a common choice for fresh water and lightly exposed hardware. A polished finish keeps the surface smooth and easy to clean, and regular rinsing helps prevent tea staining in salt water.
- Part number: 464987
- Material: 304 stainless steel
- Finish: Polished
- Length: 34 in.
- Type: Adjustable
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Foot tread plate in polished 316 stainless steel, designated R33. It provides a durable step surface at a boarding or platform location.
Foot tread plates are fitted where crew step on and off the boat, often with wet feet. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: 407419
- Material: 316 stainless steel
- Finish: Polished
- Designation: R33
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an actuated swim platform kit with step, built in 316 stainless steel with 2205 stainless steel gears, revision Delta. The actuated mechanism moves the platform and step into position for boarding and swimming.
Actuated swim platforms are mounted at the transom and spend much of their life wet. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. 2205 is a duplex stainless steel with high strength, which suits loaded gear components.
- Part number: 407071
- Material: 316 stainless steel, 2205 stainless steel gears
- Finish: Bead blast / MEP
- Revision: Delta
- Fitment: R-Series 2021
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a foot tread plate in polished 316 stainless steel, referenced as R6'20. It provides a durable stepping surface and protects the area underneath from wear.
Tread plates are typically installed on swim platforms, boarding steps and gunwale step areas. These spots stay wet and see heavy foot traffic, so 316 stainless is preferred over 304 for its better resistance to salt water pitting.
- Part number: 406724
- Material: 316 stainless steel
- Finish: Polished
- Reference: R6'20
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A 316 stainless steel rail finished in black with blue thread, cross referenced as 401351-BLUE. Rails like this give passengers a secure handhold while the boat is moving.
Grab rails are used along consoles, gunwales and seating. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. The black and blue treatment adds a color accent and a better grip surface.
- Part number: 406661
- Material: 316 stainless steel
- Finish: Black with blue thread
- Reference: 401351-BLUE
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Long replacement bolts for part 406562. They are used to fasten or reinstall the related swim platform assembly.
Swim platform fasteners are frequently submerged and loaded, so fasteners should match the parent assembly and be inspected for corrosion during service. Correct length helps achieve full thread engagement.
- Part number: 406562-LG BOLT
- Length: 4 in.
- Type: Replacement bolts for 406562
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Two step telescoping boarding ladder that mounts under the platform, with a locking feature, in polished 316 stainless steel. It extends for reboarding and locks when stowed.
Under platform ladders stay out of sight but are submerged during use. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: 404802
- Material: 316 stainless steel
- Finish: Polished
- Steps: 2, telescoping, locking
- Mounting: Under platform
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a polished 316 stainless steel dash console keeper, revision B. It holds a dash panel or console door closed by engaging the latch or catch.
Console keepers are used on dash panels, glove boxes and console doors at the helm. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: 403731
- Material: 316 stainless steel
- Finish: Polished
- Revision: B
- Fitment: A29, '20
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a backrest rail in polished 316 stainless steel, referenced as A29-19. It serves as a hand hold and a support rail at a seat backrest.
Backrest rails are typically fitted to console seats, leaning posts and bench backs where passengers need something to grip. 316 stainless resists chloride pitting better than 304, and the polished surface is smoother to the hand and easier to keep free of staining.
- Part number: 403611
- Material: 316 stainless steel
- Finish: Polished
- Reference: A29-19, Rev. A
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A transom rail designated A29, Revision B, which adds a tow point. The rail gives crew a handhold at the transom and provides a fixed point for a tow line.
Transom rails take load from people and lines and sit in constant spray. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: 403605
- Material: 316 stainless steel
- Finish: Polished
- Designation: A29, Rev. B
- Feature: Added tow point
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A head door latch with an integrated lock, used to secure the head compartment door. It holds the door closed underway and allows the compartment to be locked.
Head door latches are used in consoles and cabins where the hardware is handled often and exposed to humid salt air. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: 403598
- Material: 316 stainless steel
- Finish: Polished
- Application: Head door
- Features: With lock
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Tread plate with a 316 stainless steel frame and fasteners and a rubber tread surface, revision B, designated 30SC. It provides a non-slip step surface on the swim platform or boarding area.
Tread plates are used on swim platforms and boarding steps that are often wet. The 316 stainless frame resists salt corrosion, while the rubber tread gives secure footing.
- Part number: 403502
- Material: 316 stainless steel frame and fasteners, rubber tread
- Revision: B
- Designation: 30SC
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a starboard gunwale end cap in cast, polished 316 stainless steel. It closes off the end of the gunwale cap or rub rail and gives the gunwale a finished edge.
Gunwale end caps sit at the transom or bow ends of the gunwale where they take impact from lines, fenders and docks. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. Casting allows a formed profile, and polishing helps the surface shed salt.
- Part number: 403428
- Material: 316 stainless steel, cast
- Finish: Polished
- Side: Starboard
- Fitment: 30SC, '18
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an offset receiver for a head door, in polished 316 stainless steel, referenced as R25. The receiver is the strike that the door latch engages to hold the head door closed.
Head door receivers are mounted on the door frame or bulkhead inside the console or cabin. 316 stainless resists salt air corrosion better than 304, and the polished finish keeps it clean looking in an area that is often humid and poorly ventilated.
- Part number: 402612
- Material: 316 stainless steel
- Finish: Polished
- Style: Offset
- Reference: R25
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A slide latch for a head door, listed at 3 1/4. It holds the head compartment door closed underway and releases with a simple slide action.
Head doors open and close often and need a latch that stays positive in a seaway. Ask our sales team for material and finish details before ordering.
- Part number: 402501
- Type: Slide latch
- Application: Head door
- Size: 3 1/4
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A port side engine vent that allows air flow into the engine compartment while covering the opening in the hull side. It provides ventilation while finishing the cutout.
Engine vents sit on the hull sides where they take direct spray and running water. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. This part is both polished and electropolished for a smooth, passivated surface.
- Part number: 402392
- Material: 316 stainless steel
- Finish: Polished and electropolished
- Side: Port
- Model reference: 336 '13
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Front walk through support component for the port and starboard sides, supplied in a mill finish. It is a structural part used at the forward walk through area of the boat.
A mill finish is the untreated surface as produced, which suits parts that will be bonded, glassed in, covered or finished by the builder.
- Part number: 30100128
- Finish: Mill
- Side: Port and starboard
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an outrigger plate set in a mill finish, for the port and starboard sides. The plates provide the mounting base for outrigger hardware on the boat.
Outrigger plates are typically installed on T-tops, hard tops or gunwales to anchor outrigger bases. A mill finish is uncoated, so the part is typically installed out of sight or finished by the builder to suit the build.
- Part number: 30100118
- Finish: Mill finish
- Side: Port and starboard
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an aluminum mounting pad measuring .250 x 4 x 6 inches, made to attach to round pipe. It provides a flat mounting surface on tubing for brackets, accessories or panels.
Pipe pads are commonly used on T-tops, towers, rails and frames where hardware needs to be fastened to tube. The brushed anodized finish adds a hard oxide layer to the aluminum that improves corrosion and wear resistance in salt air.
- Part number: 30100043
- Material: Aluminum
- Finish: Brushed anodized
- Dimensions: .250" x 4" x 6"
- Application: Round pipe
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A round aluminum mounting pad, .250" thick and 5" in diameter, with four holes. It provides a flat, solid base for mounting hardware and spreads the load across a wider area.
Used under fittings on decks, consoles and structural members. Anodizing builds a hard oxide layer on the aluminum that resists corrosion and wear while keeping the part light. A brushed surface gives a uniform satin appearance.
- Part number: 30100042
- Material: Aluminum
- Finish: Brushed anodized
- Dimensions: .250" x 5" round
- Holes: 4
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A round aluminum mounting pad with 4 fastener holes. Pads of this type act as a mounting base or backing surface that spreads load from fittings into the surrounding structure.
Mounting pads are used under hardtops, leaning posts and deck hardware where a flat, stable base is needed. Anodizing builds a hard oxide layer on the aluminum that improves corrosion and wear resistance in a marine environment. A brushed finish gives a uniform appearance.
- Part number: 30100018
- Material: Aluminum
- Finish: Brushed anodized
- Dimensions: .250 in. x 5 in. round
- Holes: 4
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Aluminum pad measuring 0.250 by 3 by 4.375 inches with a brushed anodized finish. It is used as a support or backing pad to spread load at a mounting point.
Aluminum pads are used for brackets and structural hardware where low weight matters. Anodizing builds a hard oxide layer on the aluminum that resists corrosion and wear far better than bare metal in a marine setting.
- Part number: 30100011
- Material: Aluminum
- Finish: Brushed anodized
- Dimensions: 0.250 in x 3 in x 4.375 in
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a polished 316 stainless steel armrest bracket. It mounts the armrest to the seat frame and carries the load placed on the armrest.
Armrest brackets are used on helm and companion seats, where they are exposed to sun, spray and constant contact. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater. A polished surface is smoother and sheds salt and moisture more readily, which helps limit tea staining.
- Part number: 262755
- Material: 316 stainless steel
- Finish: Polished
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an armrest pocket gasket for the forward armrest of a 53' double sleigh seat. It combines an aluminum component with black EVA foam to seal and cushion the armrest pocket.
Gaskets like this sit between seating components to close gaps, reduce rattle and keep water out of the pocket. Aluminum does not rust, and closed cell EVA foam resists water absorption, so the assembly holds up in a wet cockpit.
- Part number: 260001859A
- Material: Aluminum with black EVA foam
- Application: 53' double sleigh seat, forward armrest pocket
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A 53 double sleigh seat armrest pocket gasket for the forward armrest. It combines an aluminum component with black EVA foam to seal and cushion the armrest pocket.
EVA foam resists water absorption and gives a soft, close fit against surrounding parts, while aluminum keeps the assembly light and corrosion resistant. Used in seating assemblies where fit and finish are visible to the owner.
- Part number: 260001858A
- Material: Aluminum with black EVA foam
- Designation: 53 double sleigh seat
- Position: Forward armrest
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A stainless steel end cap for the aft deck terrace insert. End caps close off and finish the open end of a trim or insert section.
End caps on deck inserts are exposed to foot traffic, spray and standing water. Stainless steel resists corrosion and keeps a clean appearance with routine rinsing.
- Part number: 2429950
- Material: Stainless steel
- Location: Aft deck terrace insert
- Reference: SXO350-26 (2.0)
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Single lever in 316 stainless steel, revision B. It operates a latch mechanism on a door, hatch or compartment.
Latch levers are handled often and sit in exposed areas of the boat. 316 stainless steel carries molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304, so it is the standard choice for exposed hardware on saltwater boats.
- Part number: 2373280
- Material: 316 stainless steel
- Type: Single lever
- Revision: B
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a 316 stainless steel latch, reference BW405CQ-20, for a starboard lounger backrest, revision B. It secures the backrest in position so it stays locked until released.
Lounger backrest latches are used on convertible and adjustable seating where the backrest is repositioned often. 316 stainless steel contains molybdenum, which gives it better resistance to chloride pitting and crevice corrosion than 304 grades in saltwater.
- Part number: 2333347
- Material: 316 stainless steel
- Reference: BW405CQ-20, Rev. B
- Side: Starboard
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an anchor roller, referenced as BW380OR-18. An anchor roller guides the anchor rode over the bow and gives the anchor a place to seat when it is retrieved.
Anchor rollers are mounted at the bow on the deck or in an anchor locker opening. Match the reference number to your current part to confirm it is the correct replacement.
- Part number: 2305467
- Reference: BW380OR-18
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An angled drain grate for a transom seat toe kick, designated 48. It covers the drain opening so water clears the deck while debris and feet stay out of the drain.
Drain grates sit where water collects and stays longest. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless. A polished surface sheds salt and grime and is easier to keep clean on the line and in service.
- Part number: 17559A
- Material: 316 stainless steel
- Finish: Polished
- Designation: 48
- Location: Transom seat toe kick, angled
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A straight drain grate for the toe kick area of a transom seat. It covers the drain channel, letting water pass through while keeping the opening protected from debris and foot traffic.
Drain grates sit in the cockpit sole and seat bases where water collects, so the material is regularly wet with salt water. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 grade. A polished finish leaves a smooth surface that sheds salt and is easier to keep clean.
- Part number: 17558A
- Material: 316 stainless steel
- Finish: Polished
- Size reference: 48
- Location: Transom seat toe kick
- Style: Straight
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
Hardtop backup pad with a raw finish. It sits behind the hardtop mounting point to spread fastener load and reinforce the attachment area.
Backup pads are used wherever hardtop legs or frames bolt through a laminate or structure. A raw finish suits parts that are hidden, bonded or finished by the builder.
- Part number: 15.8300.001/1220
- Finish: Raw
- Fitment: Sea Pro Boats hardtop
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is an aluminum hinge, powder coated white with an orange peel texture. It lets a hatch, lid or door pivot open while matching white gelcoat and white trimmed components.
White hinges are used where builders want hardware to blend with the surrounding surface rather than stand out. Powder coating adds a durable barrier against UV and salt spray, and the orange peel texture helps hide minor scuffs.
- Part number: 108976
- Material: Aluminum
- Finish: White powder coat, orange peel texture
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
This is a replacement hardware kit for a Solace anchor roller. It includes the nuts, bolts and washers used to mount the roller assembly.
Anchor roller hardware sits at the bow, where it takes direct salt spray and repeated loading from the anchor rode. The 316 stainless steel fasteners resist pitting and crevice corrosion better than 304, and replacing the full set keeps the alloy consistent so mixed metals are avoided.
- Part number: 105848- HDWR
- Material: 316 stainless steel
- Quantity: 8 each nuts, bolts and washers
- Fitment: Solace anchor roller
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
A transom cap for Sportsman boats, specified for PH43 with triple 600s. The cap covers and finishes the top edge of the transom and protects it from wear.
Transom caps take foot traffic, line chafe and constant spray. 316 stainless steel contains molybdenum, which gives it better resistance to pitting and crevice corrosion from salt spray than 304 stainless.
- Part number: 105720
- Material: 316 stainless steel
- Configuration: PH43, triple 600s
- Fitment: Sportsman
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
An upper hardtop pad for the starboard side. Hardtop pads act as the mounting interface between the hardtop frame and the top, spreading load at the connection point.
Hardtop mounting pads are exposed to sun, spray and constant vibration underway, so material choice and correct fastening are important. Isolating dissimilar metals at the joint helps reduce galvanic corrosion.
- Part number: 104708
- Location: Upper hardtop
- Side: Starboard
- Model reference: 37LF
- Warranty: 1 year
Stock on hand ships from our Summerville, SC warehouse. For volume pricing, custom finishes or a matching part for your build, contact sales@pwmarineoem.com.
No results found
No results match your search. Try removing a few filters.